Halvautomatisk strekkfilm maskin
6 individuella program
Försträckning: 1-210% med Botten-/ toppvarv: 1-7
Til smøring av pakkemaskiner anbefaler vi Fluid Film som ikke trekker til seg skitt.
Sträckfilmar oregelbundet formade gods. Använd gaffeltruck/ pallyftare för att lasta på godset. Operatören startar stäckfilmningen, skär och fäster filmen manuellt.
Alla Cyklopmaskiner klarar en filmtjocklek på 9-35 (my) i både blåst och cast kvalitet, försträckt eller vanlig film. Observera att det bästa resultatet och lägsta konstnad per pall alltid kommer att erhållas med hjälp av högkvalitativa filmer oavsett tjocklek.
Filmbredd: 500 mm Diameter: max. 250 mm Diameter, kärna: 76 mm
1-fas, 240V, 50Hz
1 200 mm.
1 000 mm
2 200 mm.
2 000 kg
1-fas, 240V, 50Hz
Liability for defects; Warranty
Pursuant to the provisions of this Warranty Cyklop Teknik AB (herein after referred to as “CT”) shall remedy any defect or non-conformity in the Works resulting from faulty design, materials or workmanship. Under no event CT assumes a guarantee for properties and conditions.
CT’s liability is limited to defects in the works, which appear within a period of 12 months with a daily use for 1 shift (8 hours) from transfer of risk or taking over of the goods. If the daily use exceeds the agreed use, this warranty period shall be reduced proportionately. If taking-over has been delayed for reasons for which the purchaser is responsible, CT’s liability for defects shall not be extended beyond 18 months after delivery.
The purchaser shall without undue delays notify CT in writing, describing the defect, of any defect that appears. Such notice shall under no circumstance be given later than 2 weeks after the expiry period given under sect. 2. If the purchaser fails to notify CT in writing of a defect within the time limit set forth in this clause, he loses his right to have the defect remedied.
The expiration of the period stated under Section 2 is suspended with the occurrence of the defect and continues with the effected remedy of the defect.
Provided that the defect may cause serious damage, the purchaser shall immediately inform CT in writing. The purchaser shall bear the risk of damage resulting from his failure so to notify.
On receipt of the notice CT shall remedy the defect without undue delay at his own cost. Provided the expected costs for CT to remedy the defect are unreasonably high, CT may assign a third party to remedy the defect. The purchaser shall remedy minor defects after consultation with CT. The purchaser shall at his own expense arrange for any dismantling and reassembly of equipment other than the works to the extend that this is necessary to remedy the defect.
If the purchaser has given notice to CT and no defect is found for which CT is liable, CT shall be entitled to compensation for the costs incurred as a result of the notice.
Wear and tear parts are excluded from liability. Condition precedent to CT’s liability is the regular, proper and verifiably professionally carried out maintenance, the use of CT materials and wear and spare parts as well as the appropriate storage of the goods. No remedy of a defect shall be considered to be an acknowledgement.
If the purchaser has given such notice as mentioned in Section 3 and no defect is found for which CT is liable is found, CT shall be entitled to compensation for all costs incurred as a result of this notice.
Cyklop Teknik will compensate the customer for his expenses in connection with repairs, travels etc. with a fix sum of SEK 400 per hour or 3 500 per day inclusive travel costs.
This compensation will be paid if:
- The purchaser at first has been in contact with the CT Technical
Phone Support and that the problem couldn’t be solved by phone
- CT has been informed and accepted that the customer intends to
send his personal to the end-user.
- The purchaser has sent a correctly filled in “Claim form” and that CT
has accepted the claim as warranty. The claim form can also be sent
to CT after the customer have been at the end-user